Minutes of Proceedings of the Institution of Civil Engineers, Band 51Institution of Civil Engineers, 1878 |
Im Buch
Ergebnisse 1-5 von 8
Seite 50
... girders was a useful one , putting engineers more on a level , and preventing their employers . from complaining about unnecessary weight of the parts . The effect might be to a certain extent to stop inventions ; but was not that often ...
... girders was a useful one , putting engineers more on a level , and preventing their employers . from complaining about unnecessary weight of the parts . The effect might be to a certain extent to stop inventions ; but was not that often ...
Seite 177
... Girders for Single - span Railway Bridges . " 5. A Miller Prize to Nicholas Watts , 1 Stud . Inst . C.E. , for his Paper on " Mechanical Puddling in the Manufacture of Iron . " 6. A Miller Prize to William James Chalk , Stud . Inst ...
... Girders for Single - span Railway Bridges . " 5. A Miller Prize to Nicholas Watts , 1 Stud . Inst . C.E. , for his Paper on " Mechanical Puddling in the Manufacture of Iron . " 6. A Miller Prize to William James Chalk , Stud . Inst ...
Seite 291
... girders were required to bear a tensile strain of 4 tons ; the cross and longitudinal girders 4 tons per square inch ; and all parts of cast steel a strain of 10 tons per square inch . The tenders of MM . Filleul - Brohy having been ...
... girders were required to bear a tensile strain of 4 tons ; the cross and longitudinal girders 4 tons per square inch ; and all parts of cast steel a strain of 10 tons per square inch . The tenders of MM . Filleul - Brohy having been ...
Seite 292
... girders with parallel straight booms , compression and tension bars , and two footways each 61 feet wide . The clear ... girders , and to support the footway cantilevers . The cross and longitudinal girders and the wind stays or braces ...
... girders with parallel straight booms , compression and tension bars , and two footways each 61 feet wide . The clear ... girders , and to support the footway cantilevers . The cross and longitudinal girders and the wind stays or braces ...
Seite 294
... girders of two arched steel tubes , placed one above the other and connected by bracing , were adopted . The western ... girders are 12 feet for the centre ones and 16 feet for the side ones . The piers at the springing of the arches are ...
... girders of two arched steel tubes , placed one above the other and connected by bracing , were adopted . The western ... girders are 12 feet for the centre ones and 16 feet for the side ones . The piers at the springing of the arches are ...
Inhalt
302 | |
309 | |
315 | |
319 | |
325 | |
331 | |
337 | |
344 | |
194 | |
213 | |
237 | |
261 | |
277 | |
284 | |
290 | |
296 | |
350 | |
356 | |
362 | |
371 | |
377 | |
399 | |
410 | |
411 | |
Andere Ausgaben - Alle anzeigen
Häufige Begriffe und Wortgruppen
acres amount Author average Bilbao Board of Trade boilers Bouches-du-Rhône bridge cable caisson canal carried cent centre chain cliff coal cofferdam Company compound engine condenser construction cost cubic feet cubic yards curves cylinder depth discharge Durance experiments factor of safety feet long foot fuel furnace girders groynes horizontal Hornsea inches inches in diameter inches thick increased indicated HP indicator diagrams Inst iron irrigation Kilnsea length lineal load locomotive loss of land marine masonry matter maximum mètre miles minute nickel obtained ordinary phylloxera pier piles placed plates pressure propeller quantity rails railway resistance river rope sand screw Sestao shaft shipowner side span speed square inch steam shipping steamers steel struts surface surface condensers tacheometer temperature tion tonnage tons tramway tubes tunnel valves velocity vessels wall weight wheels width wire Withernsea yards per annum